-
1
Combine everything except the brisket in a small bowl.
-
2
Place the brisket fat-side down on a work surface.
-
3
Sprinkle it evenly with half of the curing mixture and gently pat the mixture onto the meat.
-
4
Let it sit until the curing mixture hydrates, darkens in color, and adheres to the brisket, about 25 minutes.
-
5
Flip the brisket over and sprinkle it evenly with the remaining curing mixture.
-
6
Let it sit until the curing mixture hydrates, darkens in color, and adheres to the brisket, about 15 minutes more.
-
7
Place the brisket in an extra-large (2- to 2-1/2-gallon) resealable plastic bag.
-
8
(Alternatively, you can place it in a roasting pan and cover it tightly with aluminum foil.)
-
9
Refrigerate for 7 days, flipping the brisket every 2 days.
-
10
On the eighth day, fit a wire rack over a baking sheet.
-
11
Remove the brisket from the bag and gently pat off any excess moisture with paper towels.
-
12
Place it on the rack fat-side up and refrigerate uncovered overnight.
-
13
Let the brisket sit at room temperature for 1 hour.
-
14
Meanwhile, remove all of the racks from the oven except one arranged in the lowest position.
-
15
Heat the oven to 200 degrees F.
-
16
Line the inside of a roasting pan crosswise with the foil, overlapping it in the center of the pan by about 1 inch.
-
17
Make sure that the bottom and sides of the pan are completely covered and that the excess foil extends over the long sides and slightly up and over the short sides of the pan.
-
18
Scatter the wood chips in an even layer over the foil in the bottom of the pan.
-
19
Fit a roasting rack over the chips.
-
20
(The roasting rack should sit at least 1 1/2 inches above the bottom of the pan.
-
21
You can try flipping it over if needed.
-
22
If your roasting rack still sits too low, use a wire steaming or cooling rack that sits at least 1 1/2 inches above the bottom of the pan.)
-
23
Place the brisket on the rack fat-side up.
-
24
Bring the long edges of the foil up to meet in the middle.
-
25
Fold the foil down three times and crimp it to close tightly, making sure its not touching the brisket so that the smoke can circulate around the meat.
-
26
Bring up the foil on the sides to meet the top seam and crimp, making sure the entire rack and brisket are completely surrounded with foil and there are no gaping holes.
-
27
Place the roasting pan across two burners over medium-high heat until a steady stream of smoke pours out of the top seam of the foil bundle, about 5 minutes.
-
28
(This step doesnt produce a ton of smoke, but you still may want to open a window or turn on the fan above your range.)
-
29
Place the pan in the oven and smoke until the pastrami reaches 140 degrees F on an instant-read thermometer, about 4 to 6 hours.
-
30
Remove the pan from the oven and carefully open the top seam of the foil.
-
31
Remove the rack and pastrami to a baking sheet or heatproof work surface; set aside.
-
32
Discard the foil and smoking wood chips.
-
33
(You can immediately proceed with the recipe and steam the pastrami, or cool the meat to room temperature and refrigerate it tightly wrapped in plastic wrap for up to 24 hours.)
-
34
Increase the oven temperature to 325 degrees F and keep the rack in the lowest position.
-
35
Place the pastrami fat-side up in the empty roasting pan; set it aside.
-
36
Place the water in a large saucepan, cover with a tightfitting lid, and bring to a boil over high heat.
-
37
Place the roasting pan on the oven rack and pour enough boiling water to reach halfway up the thickest side of the pastrami, being careful not to pour it directly onto the pastrami.
-
38
(You may not need all of the water.)
-
39
Cover the roasting pan tightly with foil.
-
40
Steam the pastrami in the oven until knife tender, about 3 hours.
-
41
Remove the pastrami to a cutting board and let it sit for 10 minutes before slicing against the grain.
